Now lets see how I did the ribbon weaving on the Hairband. For the
ribbon weaving I used ½” white ribbon – approx 5mtrs (the length on the ribbon
may vary depending on the hairband size).
1. I started the weaving from both the ends of
the ribbon and named them as left ribbon & right ribbon. Made a ½” loop on the
right ribbon. (The loop size will depend on your ribbon size.)
2. Then made a loop on the left ribbon and
passed it through the right loop.
3. Next made a loop on the right ribbon and then passed it through the left loop.
4. Then pulled the left ribbon to tighten the
loop.
5. To secure the entire weaving I turned it around and using silicon glue stuck the ribbon at the point the needle is inserted in
the picture above. Once the silicon glue was dry, I snapped off the extra ribbon end
seen below the needle.
6. After the weaving was secure it looked like
this.
7. Then turned the entire weaving to the front and
made a loop on the left ribbon and passed it through the right ribbon loop. Then pulled the right ribbon to tighten the loop. Step 3, 4 & 7 were repeated till I got the
desired length of the weave. The length depends on the hairband size.
8. The ribbon weaving looked like this.
9. Once the desired length of the weaving was achieved, I secured the right ribbon end by sticking the ribbon at the point the needle is shown in the picture above.
10. Then the left ribbon end was secured at the back of the weaving at the point the needle is showing in the picture above.
Once the glue was dry I snapped off the extra loop.
11. Finally the weaving was secured and the end
looked like this.
12. Lastly I adhered the ribbon weaving to the
hairband using Itsy Bitsy’s Silicon Glue and then adhered the flower to the
hairband at the desired place.
Brooch Pin & Hair Clip
Lets check out how these flowers were formed.
1. I started by covering the Saree brooch
clip with felt sheet.
2. Same I did with the barrette clip. Wrapped
it with felt sheet in & out
3. Next I took 1” light green satin ribbon
and sealed its edge using a T-light candle. Then folded the ribbon edge
diagonally as shown in the picture above and cut it at the inside edge. This
gave me a square. I needed 5 such squares as the flower has 5 petals.
4. Here I took each square & folded it
diagonally.
5. Then holding the ribbon as in picture 4, I
made the right corner to meet the top centre point and sealed this edge using
T-light candle.
6. Repeated the same with the other corner.
7. Lastly folded the petal backward and
holding it with the tweezer as shown in the picture above, sealed the bottom
corner from behind. It looked like pinched from the front.
The same process was used to make 15 Teal colour petals. Once all
the petals were ready I assembled each flower with 5 petal on a small cardstock
circle with silicon glue and then stuck 1 teal flower on the saree brooch pin
and 3 flowers on the barrette clip.
Hair Ponytail Band
Lets see how this beauty is created.
1. I started by folding the right bottom corner to the upper edge and then using a straight tweezer coiled the corner upto ½”.
2. Holding the coiled edge I started stitching (running stitch) the upper edge upto the folded corner.
3. Once the upper edge was secure with the running stitch, I folded the ribbon backward along the vertical edge.
4. And then the new formed edge was again folded diagonally as in step 1 to meet the upper edge.
5. Again I secured this open edge by running stitch.
6. I continued doing step 3 & 4 few more times and then slowly pulled the thread from the starting point against the ribbon to form gathered petals as in the picture above.
7. Again I repeated steps 3 – 6 till I achieved desired no of petals for the Rose. The last petal was then secured by a knot and the extra ribbon was cut. Lastly I started coiling the rose with my hand from the beginning point making sure that the base is flat and not conical. The last petal was secured using silicon glue.
Now let’s assemble the entire band.
8. To give a base to the ribbon rose I had used a white cotton lace from my stash. I started with running stitch on the upper edge.
9. Once the desired length was achieved, I pulled the thread from the beginning point and formed a gathered flower. The end edge was stitched to secure it.
10. I had used the green gross grain ribbon to give a contrast colour and look of leaves. Just made simple loops as shown in the picture above and stuck all the layers in the centre using silicon glue.
11. The white lace flower & the green loops where then stitched to the black band. A pearl was used inside the black band behind the white lace flower to secure the stitch. This helped in avoiding the stitch to come off by fraying the band off.
Mini Hair Clip
So lets see how the clip was made.
For the Light pink flower I have used ½” ribbon and the same
technique of Ribbon Rose as discussed above. The ribbon size being small it
looks a little different from the rose. Had also covered the mini barrette clip
with brown felt sheet.
For the buds I have used 1” Dark pink ribbon.
1. I cut a square out of the 1” dark pink
ribbon. Sealed the edges using a T-light candle.
2. Then folded it diagonally.
3. Again folded it diagonally to get a
smaller triangle.
4. Now holding the ribbon as shown in the
above picture, I started coiling from right corner to the left corner. I maintained
the bottom edge to be flat. Finally secured the end point with silicon glue.
5. Next i added yellow pollens to the bud
using silicon glue again.
6. For fillers I made pearl stems using wire.
For the leaves I have used 1” dark green satin ribbon.
7. I cut 2 pcs of 6 cms long 1” dark green
satin ribbon.
8. Then keeping the wrong side of the ribbon
facing up, folded the top corners to the bottom edge and then secured them by
running stitch. Then pulled the thread against the ribbon to gather the bottom
edge and secured it by a knot.
9. Lastly from the front using a straight
tweezer I pinched the top and stuck it using a T-light candle.
10. Finished Leaf.
Finally for assembling the clip I used silicon glue to stick the
flowers, then leaves, buds and lastly pearl fillers. Refer the picture above.
Love Gopi
